Terminal Escape Room Out of Space Walkthrough and Codes

Terminal Escape Room Out of Space challenges players to restore power aboard a damaged spacecraft, align planetary navigation controls, wire an emergency vehicle circuit, and launch Escape Pod 4. Created by CCF Studios on Roblox, this chapter represents Season 2, Chapter 1, Part 2 of the game. Completing the scenario requires solving four calibration puzzles, entering keypad codes 2783 and 5078, and plotting an asteroid route back to Earth.

Calibrating the Four Control Panels

Escaping the initial chamber requires collecting four square panels by repairing the power boxes, restoring the water supply, and calibrating three planetary navigation dials.

Power Boxes and Gear

Inspect the two electrical boxes mounted on the walls to restore power to the primary consoles:

1. On the slider power box, keep the middle elements in place, slide the pink arrows fully to the left, and adjust the blue piece so the red light is covered while green remains visible.
2. On the rotating power box, turn the elements until all red lights are hidden behind the covers and the green lights remain exposed.
3. Collect the mechanical Gear revealed inside the casing for later use.

Water System Grid

Examine the water maintenance diagram on the wall. The system requires exactly two illuminated buttons in every row and column, with lit buttons prohibited from touching horizontally or vertically:

1. Leave the known dark spots unselected as marked by the wall note.
2. Select the valid positions across the grid so that every row and column contains exactly two active lights without orthogonal contact.
3. Completing the grid dispenses the white panel.

Planetary Control Consoles

The remaining three panels come from the navigation regulators, which calibrate according to the Kara planetary chart:

• Asteroid Defense Control: Locate the five planets on the chart and count the surrounding asteroids from 1 to 5. The sequence is Acturu (1 asteroid), Tarrinis (2 asteroids), Xyltharis (3 asteroids), Striattus (4 asteroids), and Vaktha (5 asteroids). Rotate each knob to match the ring angles shown on the chart: horizontal for Acturu, vertical straight down for Tarrinis, slight diagonal for Xyltharis, steep diagonal for Striattus, and slight right tilt for Vaktha.
• Pathfinder Control: Follow the drawn rocket flight path connecting the planets. Set the five slider heights to match each planet's position along the dotted guide lines: bottom position for Atrius, top position for Xylthri, second highest for Tarrini, second lowest for Striattus, and middle height for Vaktha.
• Habitability Control: Consult the habitability analysis ranking planets from level 1 to level 5 (Vaktha, Xylthri, Tarrini, Striattus, and Atrius). Adjust the circular dials to match each planet's physical size in that order: largest for Vaktha, medium for Xylthri, second largest for Tarrini, second smallest for Striattus, and smallest for Atrius.

Insert all four collected panels into the wall receptacle. Rotate the pieces until the top row spells the word CODE. The bottom row reveals the sequence 2783. Input 2783 into the keypad to open the lounge door.

Lounge Access and Vehicle Rewiring

Inside the lounge, collect the Wire, Crowbar, and Jumper Cables scattered across the room. Return to the transport vehicle in the main hangar:

1. Use the Crowbar to force open the driver side car door and inspect the repair manual.
2. Attach the Jumper Cables to link the power terminal to the car.
3. Connect the Wire to access the 30-inch electrical circuit board.

The circuit puzzle requires routing electrical current from the power inputs to all positive terminals in red and negative terminals in blue without exceeding 30 total inches of wire:

1. On the left side, link the red source across adjacent nodes to energize the positive terminals.
2. Build common junction points on the right side using short wire segments rather than extending long runs around the perimeter.
3. Route 1-inch and 2-inch segments across the blue paths to bridge the negative sensors.
4. Once all sensors display active charges, the vehicle trunk pops open. Collect the Wrench stored inside.

Zero-Gravity Machine and Escape Pod 4 Codes

Proceed to the zero-gravity generator located near the debris pile. Insert the mechanical Gear collected from the electrical box, then tighten it using the Wrench.

The zero-gravity control console features five sliders that must all reach the top position. Because each push button shifts two sliders at once, adjust them in linked pairs:

1. Press the yellow and blue button twice to pair the red and blue sliders at an equal level.
2. Press the orange and green button once to elevate the green slider toward the top.
3. Use the remaining dedicated buttons to raise the aligned pairs until all five sliders rest at the highest position.
4. Pull the primary lever. Zero gravity activates, causing rocks and loose debris to float into the air.

Move to the escape pod bay. Pods 1, 2, and 3 are marked as deployed, leaving Escape Pod 4 available. Enter 1536 into the symbol display terminal beside Pod 4 to stabilize the wall cipher.

Inspect the floating notes revealed beneath the lifted rocks to decode the four-digit pod lock:

• Vertical line clue: Matches the wall pattern for 5.
• Horizontal line clue: Matches the wall pattern for 0.
• Right diagonal slant: Matches the wall pattern for 7.
• Left diagonal slant: Matches the wall pattern for 8.

Enter 5078 into the keypad beside Escape Pod 4 to unlock the boarding hatch.

Launching Escape Pod 4: Constellations and Navigation

Board Escape Pod 4 to complete the final departure sequence on the cockpit monitors.

Triangulate Position

Examine the pod layout schematic to identify the four external viewing windows:

1. Window 1 shows the circular Pisces constellation.
2. Window 2 shows the four-star Aries constellation.
3. Window 3 shows the curved Scorpio constellation.
4. Window 4 shows the Libra constellation.

Access the triangulation terminal on the left side of the cockpit and set the four slots to Pisces, Aries, Scorpio, and Libra.

Safe Route Navigation

Activate the flight navigation monitor on the right console. The system requires plotting a continuous transit route that visits every nearby meteor exactly once before concluding with a direct trajectory to Earth:

1. Begin at the spacecraft origin point and advance along the perimeter meteors.
2. Clear the outer detour nodes before stepping into the central clusters to prevent hitting dead ends.
3. Route through the final meteor directly adjacent to Earth, establishing a straight approach vector.
4. Confirm the course, pull the hatch control lever to seal the pod, and initiate the launch sequence to complete the chapter.

Standard Mode vs Beginner Mode Puzzle Solutions

Terminal allows teams to select between Standard Mode and Beginner Mode. Beginner Mode modifies the puzzle mechanics and code solutions throughout the chapter.

Frequently Asked Questions

What is the door code for the lounge in Terminal Out of Space?

In Standard Mode, the keypad code for the lounge door is 2783. In Beginner Mode, decoding the alien numerals on the wall panels yields the combination 2860.

What code unlocks Escape Pod 4?

Standard Mode uses code 5078, which is obtained by stabilizing the symbol wall with code 1536 and matching the line directions on the floating rock notes. Beginner Mode uses code derived from counting the floating colored geometric shapes.

What is the correct constellation order inside Escape Pod 4?

Standard Mode requires entering Pisces, Aries, Scorpio, and Libra into the triangulation terminal, matching the patterns visible through windows 1 through 4. Beginner Mode requires entering viewfinder IDs 1948, 3341, 2152, and 7465 to select Virgo, Aquarius, Capricorn, and Scorpio.